| СвязьПроект http://old.xdsl.ru/svpro/ |
|
| Индивидуальные настройки для каждого адресата AP-VP300 http://old.xdsl.ru/svpro/viewtopic.php?f=4&t=1221 |
Страница 1 из 1 |
| Автор: | Виктор Кукушкин [ 29 янв 2010, 08:06 ] |
| Заголовок сообщения: | Индивидуальные настройки для каждого адресата AP-VP300 |
Как задать индивидуальные параметры аудио-видеосоединения для каждого адресата адресной книги? |
|
| Автор: | Geniu$$ [ 29 янв 2010, 09:02 ] |
| Заголовок сообщения: | |
conf t сделайте разные voice class codec и video-class codec и добавьте в соответствующие dial-peer |
|
| Автор: | Виктор Кукушкин [ 01 фев 2010, 05:54 ] |
| Заголовок сообщения: | |
Что и было сделано, однако не работает. Телефоны соединяются с параметрами указанными у них в "video class codec 2000". Высылаю apos.cfg - может в нем еще какой-то косяк? ! ! APOS(tm) configuration saved from vty ! 2010/ 1/29 14:14:19 ! version 8.43.058 ! hostname proba enable password router ! username root password router administrator ! ! interface Loopback0 ip address 127.0.0.1 255.0.0.0 ! interface FastEthernet0/0 ip address 10.248.50.40 255.255.255.0 bridge-group 1 speed auto qos-control 4096 ! interface FastEthernet0/1 no ip address bridge-group 1 speed auto no qos-control ! no ip routing ip route 0.0.0.0 0.0.0.0 10.248.50.1 ! ! ! ! ftp server ! ! dns name-server 10.248.2.2 ! osd volume 9 9 5 7 10 0 powersave 60 language Russian viewmode 2 homeurl http:// fbandwidth 512 display camin 90 64 68 8 23 0 display camout 31 128 128 rbcinfo 0.0.0.0 0 0 0 initmenu none chime off chimedelay 1 initmenu none password input 2337 password level low ring 1 sscp disable flickless off dnd reject autoanswer off qos 4096 keysetup 0 h323confname Selickii h323indicator 0 signalling h323 omdelay 0 videoinput 0 1 extvideoinput ntsc ! ! ! SSCP configuration.! ! ! ! SSCP Static CM List sscp ! ! SSCP Dynamic CM List sscp ! ! sscp call-manager broadcast port 8855 logger disable logger level info ! ! ! ! ! VoIP configuration. ! ! ! Voice service voip configuration. ! voice service voip fax protocol t38 redundancy 0 fax rate disable h323 call start preferred-slow h323 call tunnel disable timeout tmohdt 300 dynamic-payload-type h264 99 no call-barring unconfigured-ip-address no voip-inbound-call-barring enable ! ! ! Voice port configuration. ! ! SPEECH voice-port 0/0 ! ! ! VIDEO voice-port 0/1 ! ! ! HQA voice-port 0/2 ! ! ! FXO voice-port 0/3 no caller-id enable ! ! ! ! ! Pots peer configuration. ! dial-peer voice 0 pots destination-pattern 1600 port 0/0 ! ! ! ! Voip peer configuration. ! dial-peer voice 1000 voip destination-pattern T session target sip-server session protocol sip voice-class codec 0 audio-class codec 1000 video-class codec 2000 no vad dtmf-relay rtp-2833 ! dial-peer voice 1001 voip destination-pattern T session target sip-server session protocol sip voice-class codec 0 audio-class codec 1000 video-class codec 2000 no vad dtmf-relay rtp-2833 preference 2 huntstop ! dial-peer voice 1002 voip destination-pattern T session target ras voice-class codec 0 audio-class codec 1000 video-class codec 2000 no vad dtmf-relay h245-alphanumeric preference 1 huntstop ! dial-peer voice 10000 voip destination-pattern F session target ip 10.248.1.7 voice-class codec 0 audio-class codec 2 video-class codec 3000 vad dtmf-relay h245-alphanumeric description gorod ! ! dial-peer voice 10009 voip destination-pattern F session target ip 10.249.15.3 voice-class codec 0 audio-class codec 2 video-class codec 3009 vad dtmf-relay h245-alphanumeric description Strejevoi ! ! ! ! ! Gateway configuration. ! gateway h323-id proba no ignore-msg-from-other-gk register ! ! ! Codec classes configuration. ! voice class codec 0 codec preference 1 g7231r53 codec preference 2 g711alaw codec preference 3 g729 codec preference 4 g7231r63 codec preference 5 g711ulaw codec preference 6 g711alaw ! video-class codec 3000 codec preference 1 mpeg4 codec parameter 1 512 30 0 ! audio-class codec 1000 codec preference 1 g7231r53 codec preference 2 g711alaw codec preference 3 g729 codec preference 4 g7231r63 codec preference 5 g711ulaw codec preference 6 g711alaw ! ! audio-class codec 1001 codec preference 1 g726r32 codec preference 2 g711ulaw codec preference 3 mp3 ! ! audio-class codec 1002 codec preference 1 g726r32 codec preference 2 g711ulaw codec preference 3 mp3 ! ! audio-class codec 1003 codec preference 1 g726r32 codec preference 2 g711ulaw codec preference 3 mp3 ! video-class codec 3009 codec preference 1 h263 codec parameter 1 128 3 0 ! video-class codec 2000 codec preference 1 h264 codec preference 2 mpeg4 codec preference 3 h263 codec parameter 1 512 30 0 ! ! ! ! SIP UA configuration. ! sip-ua fault-tolerance 10 500 sip-username 1600 sip-password 1600 sip-server 10.248.0.2 rport enable register e164 ! ! ! MGCP configuration. ! mgcp vad ! ! ! Tones ! ! ! ! line console ! line vty ! character-set encoding usa ascii xml koi8-ru mount mem 32 /osdmem ! mount mem 1024 /tmp ! ! ! sms quota 30 ! ! ptzm Заранее благодарен за ответ В. Кукушкин |
|
| Автор: | Geniu$$ [ 01 фев 2010, 10:00 ] |
| Заголовок сообщения: | |
Покажите дебаг во время звонка, вместе deb voip call deb rta ipc |
|
| Автор: | Виктор Кукушкин [ 02 фев 2010, 04:32 ] |
| Заголовок сообщения: | |
Высылаю log одного соединения: [1339.920] VM(0/0/0) play RingBack tone [1339.920] VP(0/0/0) Tx IBS signal 6/1 [1339.920] VP(0/0/0) update IBS gain 4 [1339.920] VP(0/0/0) Tx IBS dir 0 56 <H245 4> : Received TCS request. 57 <H245 4> : remote capabilities matching to local capabilities. number of capabilities = 8 1 : g7231A-5.3k 2 : g711alaw-64k 3 : g711ulaw-64k 4 : UserInput/basicString 5 : UserInput/hookflash 6 : H.264 7 : H.224 8 : H.224 58 <H245 4> : Send TCS request. 59 <H245 4> : Send TCS ack. 60 <H245 4> : Received MSD request. 61 <H245 4> : Send MSD ack(slave). 62 <H245 4> : Received TCS ack.. 63 <H245 4> : Received MSD ack(master). 64 <H245 4> : Received OLC request. H323_RTPChannel::Start called ! Receiver ? 1 ---------------------------------------------------------------------- channel number = 101 bandwidth used = 53 session id = 1 capability (num) = 1 capability (type) = 9 local data port = 23020 local control port = 23021 local address = 10.248.50.40 remote data port = 23038 remote control port = 23039 remote control address = 10.248.50.41 remote data address = 10.248.50.41 ---------------------------------------------------------------------- 65 <Chan 4> : Open - number(101) direction(receive) session(voice) c odec(g7231A-5.3k) - Local : Data(23020) Cont(23021) Addr(10.248.50.40) - Remote : Data(23038) Cont(23039) DataAddr(10.248.50. 41) ContAddr(10.248.50.41) [1344.795] RTA(0/0/0) Rx RS_LISTEN_REQ callId=4 ssId=1 G7235 peer=10.248.50.41 mp=23020/23021 hp=23038/23039 [1344.795] VM(0/0/0) vopp idle [1344.795] VP(0/0/0) close channel [1344.795] VM(0/0/0) start codec replace timer to G7235 66 <H245 4> : Send OLC ack. 67 <H245 4> : Received OLC request. H323_RTPChannel::Start called ! Receiver ? 1 ---------------------------------------------------------------------- channel number = 102 bandwidth used = 100 session id = 2 capability (num) = 8 capability (type) = 6 local data port = 23022 local control port = 23023 local address = 10.248.50.40 remote data port = 23040 remote control port = 23041 remote control address = 10.248.50.41 remote data address = 10.248.50.41 ---------------------------------------------------------------------- 68 <Chan 4> : Open - number(102) direction(receive) session(video) c odec(H.264) - Local : Data(23022) Cont(23023) Addr(10.248.50.40) - Remote : Data(23040) Cont(23041) DataAddr(10.248.50. 41) ContAddr(10.248.50.41) [1344.800] VM(0/1/0) Video H264 RTP payload type TxPT=0x63, RxPT=0x63 [1344.800] RTA(0/1/0) Rx RS_LISTEN_REQ callId=4 ssId=2 H.264 peer=10.248.50.41 mp=23022/23023 hp=23040/23041 [1344.800] RTA(0/1/0) Rx MM_CONN_REQ [82 83 81 88 9e 80 ] peerId(-1) [ [Dec] H.264 CBR 512K f_30 320x240 ] [1344.800] VM(0/1/0) MM video enable [Dec] 69 <H245 4> : Send OLC ack. [1344.805] VG(0) VideoEncoderEnable [0] [1344.805] VG(0) VideoDecoderEnable [1] [1344.805] VG(0) DecoderInterrupt [0] [1344.805] VG(0) VideoMUTE [0] [1344.805] VG(0) AudioEncoderEnable [0] [1344.805] VG(0) AudioDecoderEnable [0] 70 <H245 4> : Received OLC request. H323_RTPChannel::Start called ! Receiver ? 1 ---------------------------------------------------------------------- channel number = 103 bandwidth used = 100 session id = 3 capability (num) = 9 capability (type) = 7 local data port = 23024 local control port = 23025 local address = 10.248.50.40 remote data port = 23042 remote control port = 23043 remote control address = 10.248.50.41 remote data address = 10.248.50.41 ---------------------------------------------------------------------- 71 <Chan 4> : Open - number(103) direction(receive) session(data) co dec(H.224) - Local : Data(23024) Cont(23025) Addr(10.248.50.40) - Remote : Data(23042) Cont(23043) DataAddr(10.248.50. 41) ContAddr(10.248.50.41) 72 <H245 4> : Send OLC ack. 73 <Q931 4> : Received CONNECT 74 <H225 4> : Remote Endpoint (AddPac VoIP,8.28,97,0,22) 75 <H245 4> : Send OLC request. 76 <H245 4> : Send OLC request. 77 <H245 4> : Send OLC request. 78 <Call 4> : Connected from(ffffffff) [1344.810] RTA(0/0/0) Rx CC_CONNECT_RSP peerId(0/0/0) [1344.810] VM(0/0/0) T38 Fax disabled 79 <NetEP 4> : Call with Nach.UVD established [1344.810] VM(0/1/0) Tx PrivAudCTRL to OSD, val=0 [1344.810] VM(0/1/0) Tx PrivVidCTRL to OSD, val=0 [1344.815] VG(0) VideoEncoderEnable [0] [1344.815] VG(0) VideoDecoderEnable [1] [1344.815] VG(0) DecoderInterrupt [0] [1344.815] VG(0) VideoMUTE [0] [1344.815] VG(0) AudioEncoderEnable [0] [1344.815] VG(0) AudioDecoderEnable [0] 80 <H245 4> : Received OLC ack. H323_RTPChannel::Start called ! Receiver ? 0 ---------------------------------------------------------------------- channel number = 101 bandwidth used = 53 session id = 1 capability (num) = 1 capability (type) = 9 local data port = 23020 local control port = 23021 local address = 10.248.50.40 remote data port = 23038 remote control port = 23039 remote control address = 10.248.50.41 remote data address = 10.248.50.41 ---------------------------------------------------------------------- 81 <Chan 4> : Open - number(101) direction(transmit) session(voice) codec(g7231A-5.3k) - Local : Data(23020) Cont(23021) Addr(10.248.50.40) - Remote : Data(23038) Cont(23039) DataAddr(10.248.50. 41) ContAddr(10.248.50.41) [1344.820] RTA(0/0/0) Rx RS_OPEN_REQ callId=4 ssId=1 G7235 peer=10.248.50.41 mp=23020/23021 hp=23038/23039 [1344.820] VM(0/0/0) openRTP codec G723 no change 82 <H245 4> : Received OLC ack. H323_RTPChannel::Start called ! Receiver ? 0 ---------------------------------------------------------------------- channel number = 102 bandwidth used = 100 session id = 2 capability (num) = 11 capability (type) = 6 local data port = 23022 local control port = 23023 local address = 10.248.50.40 remote data port = 23040 remote control port = 23041 remote control address = 10.248.50.41 remote data address = 10.248.50.41 ---------------------------------------------------------------------- 83 <Chan 4> : Open - number(102) direction(transmit) session(video) codec(H.264) - Local : Data(23022) Cont(23023) Addr(10.248.50.40) - Remote : Data(23040) Cont(23041) DataAddr(10.248.50. 41) ContAddr(10.248.50.41) [1344.825] RTA(0/1/0) Rx RS_OPEN_REQ callId=4 ssId=2 H.264 peer=10.248.50.41 mp=23022/23023 hp=23040/23041 [1344.825] DS: Session start, master=1 [1344.825] VM(0/1/0) RTP Tx RemoCon cmd PrivAudCTRL 0 [1344.825] RTA(0/1/0) Rx MM_CONN_REQ [81 83 81 88 9e 80 ] peerId(-1) [ [Enc] H.264 CBR 512K f_30 320x240 ] [1344.825] VM(0/1/0) MM video enable [Enc] [1344.825] VM(0/1/0) RTP Tx RemoCon cmd PrivVidCTRL 0 84 <H245 4> : Received OLC ack. H323_RTPChannel::Start called ! Receiver ? 0 ---------------------------------------------------------------------- channel number = 103 bandwidth used = 100 session id = 3 capability (num) = 12 capability (type) = 7 local data port = 23024 local control port = 23025 local address = 10.248.50.40 remote data port = 23042 remote control port = 23043 remote control address = 10.248.50.41 remote data address = 10.248.50.41 ---------------------------------------------------------------------- 85 <Chan 4> : Open - number(103) direction(transmit) session(data) c odec(H.224) - Local : Data(23024) Cont(23025) Addr(10.248.50.40) - Remote : Data(23042) Cont(23043) DataAddr(10.248.50. 41) ContAddr(10.248.50.41) [1344.830] VG(0) VideoEncoderEnable [1] [1344.830] VG(0) VideoDecoderEnable [1] [1344.830] VG(0) DecoderInterrupt [0] [1344.830] VG(0) VideoMUTE [0] [1344.830] VG(0) AudioEncoderEnable [0] [1344.830] VG(0) AudioDecoderEnable [0] [1344.855] VP(0/0/0) enable AEC [1344.855] VP(0/0/0) open channel [1344.855] VM(0/0/0) codec replaced to G7235 [1344.855] VM(0/0/0) play mute [1344.855] VP(0/0/0) Tx IBS signal 2/0 [1344.855] VP(0/0/0) update IBS gain 0 [1344.855] VP(0/0/0) Tx IBS dir 0 86 <CCA 0> : Call Connect Request from HANDSET [1344.880] RTA(0/0/0) Rx AP_SVC_REQ nSvcElem=1 rawDataLen=0 OFF_HOOK 0(handset) [1344.880] VP(0/0/0) use handset [1344.880] VP(0/1/0) add handset #@OsdSwitchedVideoSrcIndicator(terminal=1,termID=0,pvid=-1,srcAlias=0,mode=0x0) [1345.455] VG(0) video restore iIntv [6] [1345.780] VM(0/1/0) RTP Tx RemoCon cmd PrivAudCTRL 0 [1345.780] VM(0/1/0) RTP Tx RemoCon cmd PrivVidCTRL 0 [1345.795] VM(0/1/0) Tx PrivAudCTRL to OSD, val=0 [1345.795] VM(0/1/0) Tx PrivVidCTRL to OSD, val=0 [1345.800] VG(0) VideoEncoderEnable [1] [1345.800] VG(0) VideoDecoderEnable [1] [1345.800] VG(0) DecoderInterrupt [0] [1345.800] VG(0) VideoMUTE [0] [1345.800] VG(0) AudioEncoderEnable [0] [1345.800] VG(0) AudioDecoderEnable [0] [1345.820] DS: Rx fr peer 10.248.50.41 SYNC_REQ Cid=0x0 dw0=0x0 b1=0x0 b2=0x0 w3 =0x0 [1345.820] DS: Tx to peer 10.248.50.41 CMD_RSP Cid=0x0 dw0=0x9 b1=0x0 b2=0x0 w3= 0x0 [1345.820] DS: ReportGlobalInfo nClientLocal 0 [1345.825] DS: Tx to peer 10.248.50.41 SYNC_REQ Cid=0x0 dw0=0x0 b1=0x0 b2=0x0 w3 =0x0 [1345.830] DS: Rx fr peer 10.248.50.41 CMD_RSP Cid=0x0 dw0=0x9 b1=0x0 b2=0x0 w3= 0x0 [1345.830] DS: ReportGlobalInfo nClientLocal 0 [1345.875] VG(0) video update new TgRate [504] #@OsdSwitchedVideoSrcIndicator(terminal=1,termID=0,pvid=-1,srcAlias=0,mode=0x0) [1346.875] VG(0) video update new TgRate [501] [1347.875] VG(0) video update new TgRate [492] 87 <Time 0> : Gatekeeper registration retry timeout. 88 <GK 0> : Try registration to All candidated GKs exclude() exclu sive() 89 <GK 0> : Fail registration to all alternate GKs 90 <CCA 0> : Call Disconnect Request from HANDSET [1351.380] RTA(0/0/0) Rx AP_SVC_REQ nSvcElem=1 rawDataLen=0 ON_HOOK [1351.380] VP(0/0/0) use none [1351.380] VP(0/0/0) close channel [1351.380] VM(0/0/0) Tx DISCONN_CNF 91 <CEP 000000> : Disconnected(16) at Busy 92 <Call 4> : Terminated from(0) this(Local:CallClear) before(NULL) forced(0) time(1265106037) 93 <CEP 000000> : DisconnectCall at Idle [1351.380] RTA(0/1/0) Rx MM_DISC_REQ peerId(-1) [1351.380] VM(0/1/0) MM video disable [1351.380] RTA(0/0/0) Rx RS_CLOSE_REQ callId=4 ssId=1 dir=reve 94 <Chan 4> : Close - number(101) direction(receive) [1351.380] RTA(0/1/0) Rx RS_CLOSE_REQ callId=4 ssId=2 dir=reve [1351.380] VM(0/1/0) RTP Tx RemoCon cmd PrivAudCTRL 0 95 <Chan 4> : Close - number(102) direction(receive) 96 <Chan 4> : Close - number(103) direction(receive) [1351.380] RTA(0/0/0) Rx RS_CLOSE_REQ callId=4 ssId=1 dir=forw [1351.380] RTA(0/0/0) close Media socket [1351.380] RTA(0/0/0) close RTCP socket [1351.380] VM(0/1/0) RTP Tx RemoCon cmd PrivVidCTRL 0 97 <Chan 4> : Close - number(101) direction(transmit) [1351.380] RTA(0/1/0) Rx RS_CLOSE_REQ callId=4 ssId=2 dir=forw [1351.380] DS: Session stop, state=3 [1351.380] RTA(0/1/0) close Media socket [1351.385] RTA(0/1/0) close RTCP socket [1351.385] VG(0) VideoEncoderEnable [0] [1351.385] VG(0) VideoDecoderEnable [0] [1351.385] VG(0) DecoderInterrupt [0] [1351.385] VG(0) VideoMUTE [0] [1351.385] VG(0) AudioEncoderEnable [0] [1351.385] VG(0) AudioDecoderEnable [0] 98 <Chan 4> : Close - number(102) direction(transmit) 99 <Chan 4> : Close - number(103) direction(transmit) 100 <Q931 4> : Send RELEASE COMPLETE 101 <NetEP 4> : Call TO <Nach.UVD> terminated reason(Local:CallClear) 102 <CCA 0> : Call Disconnected from 0 (30) [1351.395] RTA(0/0/0) Rx CC_DISCONN_REQ CZ=0, peerId(0/0/0) [1351.395] VM(0/0/0) Tx DISCONN_CNF 103 <CEP 000000> : StopBuzzer 104 <CCA 0> : Call Disconnect Request from SPEAKER 105 <CEP 000000> : Disconnected(16) at Idle 106 <CCA 0> : Call Disconnect Request from SPEAKER 107 <Time 0> : SIP_TREGISTER timer timeout. 108 <SIP 60> : localPeer->registerStat(3) 109 <SIP 60> : ExistInRegList(localpeer) : TRUE 110 <SIP 0> : Adding authentication information 111 <SIP 61> : Send REGISTER Request 112 <SIP 61> : Receive 200 OK 113 <SIP 61> : Transaction (61 REGISTER) completed 114 <SIP 61> : Set Terminated Success for 61 REGISTE proba# term no monit proba# |
|
| Автор: | Geniu$$ [ 04 фев 2010, 12:30 ] |
| Заголовок сообщения: | |
10.248.50.41 чей это адрес его в вашем конфиге нет. Вы должны звонить сюда 10.248.1.7 либо сюда 10.249.15.3, для этих адресов у вас есть пиры. |
|
| Автор: | Виктор Кукушкин [ 05 фев 2010, 05:32 ] |
| Заголовок сообщения: | |
Для получения лога был использован config с измененными адресами абонентов: ! ! APOS(tm) configuration saved from vty ! 2010/ 2/ 2 09:48:42 ! version 8.43.058 ! hostname proba enable password router ! username root password router administrator ! ! interface Loopback0 ip address 127.0.0.1 255.0.0.0 ! interface FastEthernet0/0 ip address 10.248.50.40 255.255.255.0 bridge-group 1 speed auto qos-control 4096 ! interface FastEthernet0/1 no ip address bridge-group 1 speed auto no qos-control ! no ip routing ip route 0.0.0.0 0.0.0.0 10.248.50.1 ! ! ! ! ftp server ! ! dns name-server 10.248.2.2 ! osd volume 9 9 5 7 10 0 powersave 60 language Russian viewmode 2 homeurl http:// fbandwidth 512 display camin 90 64 68 8 23 0 display camout 31 128 128 rbcinfo 0.0.0.0 0 0 0 initmenu none chime off chimedelay 1 initmenu none password input 2337 password level low ring 1 sscp disable flickless off dnd reject autoanswer off qos 4096 keysetup 0 h323confname Selickii h323indicator 0 signalling h323 omdelay 0 videoinput 0 1 extvideoinput ntsc ! ! ! SSCP configuration.! ! ! ! SSCP Static CM List sscp ! ! SSCP Dynamic CM List sscp ! ! sscp call-manager broadcast port 8855 logger disable logger level info ! ! ! ! ! VoIP configuration. ! ! ! Voice service voip configuration. ! voice service voip fax protocol t38 redundancy 0 fax rate disable h323 call start preferred-slow h323 call tunnel disable timeout tmohdt 300 dynamic-payload-type h264 99 no call-barring unconfigured-ip-address no voip-inbound-call-barring enable ! ! ! Voice port configuration. ! ! SPEECH voice-port 0/0 ! ! ! VIDEO voice-port 0/1 ! ! ! HQA voice-port 0/2 ! ! ! FXO voice-port 0/3 no caller-id enable ! ! ! ! ! Pots peer configuration. ! dial-peer voice 0 pots destination-pattern 1600 port 0/0 ! ! ! ! Voip peer configuration. ! dial-peer voice 1000 voip destination-pattern T session target sip-server session protocol sip voice-class codec 0 audio-class codec 1000 video-class codec 2000 no vad dtmf-relay rtp-2833 ! dial-peer voice 1001 voip destination-pattern T session target sip-server session protocol sip voice-class codec 0 audio-class codec 1000 video-class codec 2000 no vad dtmf-relay rtp-2833 preference 2 huntstop ! dial-peer voice 1002 voip destination-pattern T session target ras voice-class codec 0 audio-class codec 1000 video-class codec 2000 no vad dtmf-relay h245-alphanumeric preference 1 huntstop ! dial-peer voice 10000 voip destination-pattern F session target ip 10.248.50.34 voice-class codec 0 audio-class codec 2 video-class codec 3000 vad dtmf-relay h245-alphanumeric description gorod ! dial-peer voice 10009 voip destination-pattern F session target ip 10.248.50.41 voice-class codec 0 audio-class codec 2 video-class codec 3009 vad dtmf-relay h245-alphanumeric description Strejevoi ! ! ! ! ! ! ! Gateway configuration. ! gateway h323-id proba no ignore-msg-from-other-gk register ! ! ! Codec classes configuration. ! voice class codec 0 codec preference 1 g7231r53 codec preference 2 g711alaw codec preference 3 g729 codec preference 4 g7231r63 codec preference 5 g711ulaw codec preference 6 g711alaw ! video-class codec 3000 codec preference 1 mpeg4 codec parameter 1 512 30 0 ! audio-class codec 1000 codec preference 1 g7231r53 codec preference 2 g711alaw codec preference 3 g729 codec preference 4 g7231r63 codec preference 5 g711ulaw codec preference 6 g711alaw ! audio-class codec 1001 codec preference 1 g726r32 codec preference 2 g711ulaw codec preference 3 mp3 ! audio-class codec 1002 codec preference 1 g726r32 codec preference 2 g711ulaw codec preference 3 mp3 ! audio-class codec 1003 codec preference 1 g726r32 codec preference 2 g711ulaw codec preference 3 mp3 ! video-class codec 3009 codec preference 1 h263 codec parameter 1 128 3 0 ! video-class codec 2000 codec preference 1 h264 codec preference 2 mpeg4 codec preference 3 h263 codec parameter 1 512 30 0 ! ! ! ! SIP UA configuration. ! sip-ua fault-tolerance 10 500 sip-username 1600 sip-password 1600 sip-server 10.248.0.2 rport enable register e164 ! ! ! MGCP configuration. ! mgcp vad ! ! ! Tones ! ! ! ! line console ! line vty ! character-set encoding usa ascii xml koi8-ru mount mem 32 /osdmem ! mount mem 1024 /tmp ! ! ! sms quota 30 ! ! ptzm |
|
| Автор: | Geniu$$ [ 05 фев 2010, 08:29 ] |
| Заголовок сообщения: | |
Можно ещё дебаг с начала вызова, я не вижу, что отправляет адпак. |
|
| Автор: | Виктор Кукушкин [ 08 фев 2010, 11:43 ] |
| Заголовок сообщения: | |
Высылаю новый debug: Selickii# deb voip call Selickii# deb rta ipc Selickii# term monit Selickii# 12 <CCA 0> : Call Initiate Request from SPEAKER , peer(10000) digits() addr(10.248.1.7) type(H323) plar(0) directDigit(FALSE) [496.715] RTA(0/0/0) Rx AP_SVC_REQ nSvcElem=1 rawDataLen=0 OFF_HOOK 2(speaker) [496.715] VP(0/0/0) use speaker [496.715] VP(0/1/0) add speaker [496.715] VP(0/0/0) enable AEC [496.715] VP(0/0/0) open channel 13 <CEP 000000> : Call Received 14 <CEP 000000> : Call Initiated : calledNumber() crv(0) total(0) 15 <Call 2> : ****** Call Created status(InitiatedBySPEECH) ver(8.28:2006-02-06-00-00) time(1265649792) **** 16 <CEP 000000> : Calling number(1600) 17 <CEP 000000> : Call id(8048704b-0c8b-d565-8004-0002a40701e2) callNum(2) [496.715] RTA(0/0/0) Rx AP_SVC_REQ nSvcElem=1 rawDataLen=0 TONE_PLAY DIAL [496.715] VM(0/0/0) play Dial tone [496.715] VP(0/0/0) Tx IBS signal 6/0 [496.715] VP(0/0/0) update IBS gain 4 [496.715] VP(0/0/0) Tx IBS dir 0 18 <Call 2> : Call Initiated from CCA : peer(10000), digits(), ip(10.248.1.7) 19 <NetEP 2> : InitiateOutCall: calledNum() callingNum(1600) target(10.248.1.7) 20 <NetEP 2> : DoCall: calledAddr(10.248.1.7) callingAddr(1600) [496.720] VM(0/0/0) set T38 disable by CCC [496.720] VM(0/0/0) set T38 mode STD [496.720] VM(0/0/0) Fax rate disab 21 <NetCon 2> : Voip Peer is NULL. Get default codec class 22 <NetCon 2> : Video Info : codec(3), CBR, TR(512), FR(30), Size(1) 23 <H245 2> : myGwCall(0xb418ed5c) myGwCall->hqaEnabled(0) 24 <H245 2> : SetLocalCapabilities(outbound) 25 <H323 2> : local capabilities. number of capabilities = 10 1 : g7231A-5.3k 2 : g711alaw-64k 3 : g729-8k 4 : g711ulaw-64k 5 : T.38 6 : UserInput/basicString 7 : UserInput/hookflash 8 : H.264 9 : H.224 10 : H.224 26 <CEP 000000> : StopSignal [496.720] RTA(0/0/0) Rx AP_SVC_REQ nSvcElem=1 rawDataLen=0 DTMF_STOP [496.720] VM(0/0/0) play mute [496.720] VP(0/0/0) Tx IBS signal 2/0 [496.720] VP(0/0/0) update IBS gain 0 [496.720] VP(0/0/0) Tx IBS dir 0 27 <H225 2> : Try signalling TCP connect (10.248.1.7:1720) 28 <H225 2> : Signalling TCP connect success (2) 29 <Q931 2> : Send SETUP 30 <Q931 2> : Received CALL PROCEEDING 31 <H225 2> : Remote Endpoint (AddPac VoIP,8.28,97,0,22) 32 <Q931 2> : Received ALERTING 33 <Call 2> : Alert from(ffffffff) pseudo(0) inband(0) status(CalleeInitiated) [496.760] RTA(0/0/0) Rx CC_ALERT_RSP peerId(0/0/0) [496.760] VM(0/0/0) play RingBack tone [496.760] VP(0/0/0) Tx IBS signal 6/1 [496.760] VP(0/0/0) update IBS gain 4 [496.760] VP(0/0/0) Tx IBS dir 0 34 <H245 2> : Received TCS request. 35 <H245 2> : remote capabilities matching to local capabilities. number of capabilities = 8 1 : g7231A-5.3k 2 : g711alaw-64k 3 : g711ulaw-64k 4 : UserInput/basicString 5 : UserInput/hookflash 6 : H.264 7 : H.224 8 : H.224 36 <H245 2> : Send TCS request. 37 <H245 2> : Send TCS ack. 38 <H245 2> : Received MSD request. 39 <H245 2> : Send MSD ack(master). 40 <H245 2> : Received TCS ack.. 41 <H245 2> : Received MSD ack(slave). 42 <H245 2> : Received OLC request. H323_RTPChannel::Start called ! Receiver ? 1 ---------------------------------------------------------------------- channel number = 101 bandwidth used = 53 session id = 1 capability (num) = 1 capability (type) = 9 local data port = 23008 local control port = 23009 local address = 10.248.50.40 remote data port = 23020 remote control port = 23021 remote control address = 10.248.1.7 remote data address = 10.248.1.7 ---------------------------------------------------------------------- 43 <Chan 2> : Open - number(101) direction(receive) session(voice) codec(g7231A-5.3k) - Local : Data(23008) Cont(23009) Addr(10.248.50.40) - Remote : Data(23020) Cont(23021) DataAddr(10.248.1.7) ContAddr(10.248.1.7) [500.425] RTA(0/0/0) Rx RS_LISTEN_REQ callId=2 ssId=1 G7235 peer=10.248.1.7 mp=23008/23009 hp=23020/23021 [500.425] VM(0/0/0) vopp idle [500.425] VP(0/0/0) close channel [500.425] VM(0/0/0) start codec replace timer to G7235 44 <H245 2> : Send OLC ack. 45 <H245 2> : Received OLC request. H323_RTPChannel::Start called ! Receiver ? 1 ---------------------------------------------------------------------- channel number = 102 bandwidth used = 100 session id = 2 capability (num) = 8 capability (type) = 6 local data port = 23010 local control port = 23011 local address = 10.248.50.40 remote data port = 23022 remote control port = 23023 remote control address = 10.248.1.7 remote data address = 10.248.1.7 ---------------------------------------------------------------------- 46 <Chan 2> : Open - number(102) direction(receive) session(video) codec(H.264) - Local : Data(23010) Cont(23011) Addr(10.248.50.40) - Remote : Data(23022) Cont(23023) DataAddr(10.248.1.7) ContAddr(10.248.1.7) [500.425] VM(0/1/0) Video H264 RTP payload type TxPT=0x63, RxPT=0x63 [500.425] RTA(0/1/0) Rx RS_LISTEN_REQ callId=2 ssId=2 H.264 peer=10.248.1.7 mp=23010/23011 hp=23022/23023 [500.425] RTA(0/1/0) Rx MM_CONN_REQ [82 83 81 88 9e 81 ] peerId(-1) [ [Dec] H.264 CBR 512K f_30 640x240 ] [500.425] VM(0/1/0) MM video enable [Dec] [500.430] VG(0) VideoEncoderEnable [0] [500.430] VG(0) VideoDecoderEnable [1] [500.430] VG(0) DecoderInterrupt [0] [500.430] VG(0) VideoMUTE [0] [500.430] VG(0) AudioEncoderEnable [0] [500.430] VG(0) AudioDecoderEnable [0] 47 <H245 2> : Send OLC ack. 48 <H245 2> : Received OLC request. H323_RTPChannel::Start called ! Receiver ? 1 ---------------------------------------------------------------------- channel number = 103 bandwidth used = 100 session id = 3 capability (num) = 9 capability (type) = 7 local data port = 23012 local control port = 23013 local address = 10.248.50.40 remote data port = 23024 remote control port = 23025 remote control address = 10.248.1.7 remote data address = 10.248.1.7 ---------------------------------------------------------------------- 49 <Chan 2> : Open - number(103) direction(receive) session(data) codec(H.224) - Local : Data(23012) Cont(23013) Addr(10.248.50.40) - Remote : Data(23024) Cont(23025) DataAddr(10.248.1.7) ContAddr(10.248.1.7) 50 <H245 2> : Send OLC ack. 51 <Q931 2> : Received CONNECT 52 <H225 2> : Remote Endpoint (AddPac VoIP,8.28,97,0,22) 53 <H245 2> : Send OLC request. 54 <H245 2> : Send OLC request. 55 <H245 2> : Send OLC request. 56 <Call 2> : Connected from(ffffffff) [500.435] RTA(0/0/0) Rx CC_CONNECT_RSP peerId(0/0/0) [500.435] VM(0/0/0) T38 Fax disabled 57 <NetEP 2> : Call with Nach.UVD established [500.440] VM(0/1/0) Tx PrivAudCTRL to OSD, val=0 [500.440] VM(0/1/0) Tx PrivVidCTRL to OSD, val=0 58 <H245 2> : Received OLC ack. H323_RTPChannel::Start called ! Receiver ? 0 ---------------------------------------------------------------------- channel number = 101 bandwidth used = 53 session id = 1 capability (num) = 1 capability (type) = 9 local data port = 23008 local control port = 23009 [500.445] VG(0) VideoEncoderEnable [0] [500.445] VG(0) VideoDecoderEnable [1] [500.445] VG(0) DecoderInterrupt [0] [500.445] VG(0) VideoMUTE [0] [500.445] VG(0) AudioEncoderEnable [0] [500.445] VG(0) AudioDecoderEnable [0] local address = 10.248.50.40 remote data port = 23020 remote control port = 23021 remote control address = 10.248.1.7 remote data address = 10.248.1.7 ---------------------------------------------------------------------- 59 <Chan 2> : Open - number(101) direction(transmit) session(voice) codec(g7231A-5.3k) - Local : Data(23008) Cont(23009) Addr(10.248.50.40) - Remote : Data(23020) Cont(23021) DataAddr(10.248.1.7) ContAddr(10.248.1.7) [500.445] RTA(0/0/0) Rx RS_OPEN_REQ callId=2 ssId=1 G7235 peer=10.248.1.7 mp=23008/23009 hp=23020/23021 [500.445] VM(0/0/0) openRTP codec G723 no change 60 <H245 2> : Received OLC ack. H323_RTPChannel::Start called ! Receiver ? 0 ---------------------------------------------------------------------- channel number = 102 bandwidth used = 100 session id = 2 capability (num) = 11 capability (type) = 6 local data port = 23010 local control port = 23011 local address = 10.248.50.40 remote data port = 23022 remote control port = 23023 remote control address = 10.248.1.7 remote data address = 10.248.1.7 ---------------------------------------------------------------------- 61 <Chan 2> : Open - number(102) direction(transmit) session(video) codec(H.264) - Local : Data(23010) Cont(23011) Addr(10.248.50.40) - Remote : Data(23022) Cont(23023) DataAddr(10.248.1.7) ContAddr(10.248.1.7) [500.450] RTA(0/1/0) Rx RS_OPEN_REQ callId=2 ssId=2 H.264 peer=10.248.1.7 mp=23010/23011 hp=23022/23023 [500.450] DS: Session start, master=1 [500.450] VM(0/1/0) RTP Tx RemoCon cmd PrivAudCTRL 0 [500.450] RTA(0/1/0) Rx MM_CONN_REQ [81 83 81 88 9e 81 ] peerId(-1) [ [Enc] H.264 CBR 512K f_30 640x240 ] [500.450] VM(0/1/0) MM video enable [Enc] [500.450] VM(0/1/0) RTP Tx RemoCon cmd PrivVidCTRL 0 62 <H245 2> : Received OLC ack. H323_RTPChannel::Start called ! Receiver ? 0 ---------------------------------------------------------------------- channel number = 103 bandwidth used = 100 session id = 3 capability (num) = 12 capability (type) = 7 local data port = 23012 local control port = 23013 local address = 10.248.50.40 remote data port = 23024 remote control port = 23025 remote control address = 10.248.1.7 remote data address = 10.248.1.7 ---------------------------------------------------------------------- 63 <Chan 2> : Open - number(103) direction(transmit) session(data) codec(H.224) - Local : Data(23012) Cont(23013) Addr(10.248.50.40) - Remote : Data(23024) Cont(23025) DataAddr(10.248.1.7) ContAddr(10.248.1.7) [500.455] VG(0) VideoEncoderEnable [1] [500.455] VG(0) VideoDecoderEnable [1] [500.455] VG(0) DecoderInterrupt [0] [500.455] VG(0) VideoMUTE [0] [500.455] VG(0) AudioEncoderEnable [0] [500.455] VG(0) AudioDecoderEnable [0] [500.485] VP(0/0/0) enable AEC [500.485] VP(0/0/0) open channel [500.485] VM(0/0/0) codec replaced to G7235 [500.485] VM(0/0/0) play mute [500.485] VP(0/0/0) Tx IBS signal 2/0 [500.485] VP(0/0/0) update IBS gain 0 [500.485] VP(0/0/0) Tx IBS dir 0 #@OsdSwitchedVideoSrcIndicator(terminal=1,termID=0,pvid=-1,srcAlias=0,mode=0x0) #@OsdSwitchedVideoSrcIndicator(terminal=1,termID=0,pvid=-1,srcAlias=0,mode=0x0) #@OsdSwitchedVideoSrcIndicator(terminal=1,termID=0,pvid=-1,srcAlias=0,mode=0x0) #@OsdSwitchedVideoSrcIndicator(terminal=1,termID=0,pvid=-1,srcAlias=0,mode=0x0) #@OsdSwitchedVideoSrcIndicator(terminal=1,termID=0,pvid=-1,srcAlias=0,mode=0x0) #@OsdSwitchedVideoSrcIndicator(terminal=1,termID=0,pvid=-1,srcAlias=0,mode=0x0) #@OsdSwitchedVideoSrcIndicator(terminal=1,termID=0,pvid=-1,srcAlias=0,mode=0x0) #@OsdSwitchedVideoSrcIndicator(terminal=1,termID=0,pvid=-1,srcAlias=0,mode=0x0) #@OsdSwitchedVideoSrcIndicator(terminal=1,termID=0,pvid=-1,srcAlias=0,mode=0x0) #@OsdSwitchedVideoSrcIndicator(terminal=1,termID=0,pvid=-1,srcAlias=0,mode=0x0) [501.050] VG(0) video restore iIntv [6] [501.350] VM(0/1/0) Tx PrivAudCTRL to OSD, val=0 [501.350] VM(0/1/0) Tx PrivVidCTRL to OSD, val=0 [501.355] VG(0) VideoEncoderEnable [1] [501.355] VG(0) VideoDecoderEnable [1] [501.355] VG(0) DecoderInterrupt [0] [501.355] VG(0) VideoMUTE [0] [501.355] VG(0) AudioEncoderEnable [0] [501.355] VG(0) AudioDecoderEnable [0] [501.385] VM(0/1/0) RTP Tx RemoCon cmd PrivAudCTRL 0 [501.385] VM(0/1/0) RTP Tx RemoCon cmd PrivVidCTRL 0 [501.445] DS: Rx fr peer 10.248.1.7 SYNC_REQ Cid=0x0 dw0=0x0 b1=0x0 b2=0x0 w3=0x0 [501.445] DS: Tx to peer 10.248.1.7 CMD_RSP Cid=0x0 dw0=0x9 b1=0x0 b2=0x0 w3=0x0 [501.445] DS: ReportGlobalInfo nClientLocal 0 [501.450] DS: Tx to peer 10.248.1.7 SYNC_REQ Cid=0x0 dw0=0x0 b1=0x0 b2=0x0 w3=0x0 [501.460] DS: Rx fr peer 10.248.1.7 CMD_RSP Cid=0x0 dw0=0x9 b1=0x0 b2=0x0 w3=0x0 [501.460] DS: ReportGlobalInfo nClientLocal 0 [501.715] VG(0) video update new TgRate [493] #@OsdSwitchedVideoSrcIndicator(terminal=1,termID=0,pvid=-1,srcAlias=0,mode=0x0) [502.715] VG(0) video update new TgRate [493] [503.715] VG(0) video update new TgRate [493] 64 <Time 0> : SIP_TREGISTER timer timeout. 65 <SIP 23> : localPeer->registerStat(3) 66 <SIP 23> : ExistInRegList(localpeer) : TRUE 67 <SIP 0> : Adding authentication information 68 <SIP 24> : Send REGISTER Request 69 <SIP 24> : Receive 200 OK 70 <SIP 24> : Transaction (24 REGISTER) completed 71 <Time 0> : Gatekeeper registration retry timeout. 72 <GK 0> : Try registration to All candidated GKs exclude() exclusive() 73 <GK 0> : Fail registration to all alternate GKs 74 <CCA 0> : Call Disconnect Request from SPEAKER [513.275] RTA(0/0/0) Rx AP_SVC_REQ nSvcElem=1 rawDataLen=0 ON_HOOK [513.275] VP(0/0/0) use none [513.275] VP(0/0/0) close channel [513.275] VM(0/0/0) Tx DISCONN_CNF 75 <CEP 000000> : Disconnected(16) at Busy 76 <Call 2> : Terminated from(0) this(Local:CallClear) before(NULL) forced(0) time(1265649809) 77 <CEP 000000> : DisconnectCall at Idle [513.275] RTA(0/1/0) Rx MM_DISC_REQ peerId(-1) [513.275] VM(0/1/0) MM video disable [513.275] RTA(0/0/0) Rx RS_CLOSE_REQ callId=2 ssId=1 dir=reve 78 <Chan 2> : Close - number(101) direction(receive) [513.275] RTA(0/1/0) Rx RS_CLOSE_REQ callId=2 ssId=2 dir=reve [513.275] VM(0/1/0) RTP Tx RemoCon cmd PrivAudCTRL 0 79 <Chan 2> : Close - number(102) direction(receive) 80 <Chan 2> : Close - number(103) direction(receive) [513.275] RTA(0/0/0) Rx RS_CLOSE_REQ callId=2 ssId=1 dir=forw [513.275] RTA(0/0/0) close Media socket [513.275] RTA(0/0/0) close RTCP socket [513.275] VM(0/1/0) RTP Tx RemoCon cmd PrivVidCTRL 0 81 <Chan 2> : Close - number(101) direction(transmit) [513.275] RTA(0/1/0) Rx RS_CLOSE_REQ callId=2 ssId=2 dir=forw [513.275] DS: Session stop, state=3 [513.275] RTA(0/1/0) close Media socket [513.275] RTA(0/1/0) close RTCP socket [513.280] VG(0) VideoEncoderEnable [0] [513.280] VG(0) VideoDecoderEnable [0] [513.280] VG(0) DecoderInterrupt [0] [513.280] VG(0) VideoMUTE [0] [513.280] VG(0) AudioEncoderEnable [0] [513.280] VG(0) AudioDecoderEnable [0] 82 <Chan 2> : Close - number(102) direction(transmit) 83 <Chan 2> : Close - number(103) direction(transmit) 84 <Q931 2> : Send RELEASE COMPLETE 85 <NetEP 2> : Call TO <Nach.UVD> terminated reason(Local:CallClear) 86 <CCA 0> : Call Disconnected from 0 (30) [513.290] RTA(0/0/0) Rx CC_DISCONN_REQ CZ=0, peerId(0/0/0) [513.290] VM(0/0/0) Tx DISCONN_CNF 87 <CEP 000000> : StopBuzzer 88 <CCA 0> : Call Disconnect Request from SPEAKER 89 <CEP 000000> : Disconnected(16) at Idle 90 <CCA 0> : Call Disconnect Request from SPEAKER 91 <SIP 24> : Set Terminated Success for 24 REGISTER Selickii# term monit deb rta ipc term monitnmonitomonit monit Selickii# exit Selickii> exit Для получения данного файла использовался config со следующими изменениями: hostname Selickii ! dial-peer voice 10000 voip destination-pattern F session target ip 10.248.1.7 voice-class codec 0 audio-class codec 2 video-class codec 3009 vad dtmf-relay h245-alphanumeric description proba ! video-class codec 3009 codec preference 1 h263 codec parameter 1 128 3 1 ! video-class codec 2000 codec preference 1 h264 codec preference 2 h263 codec preference 3 mpeg4 codec parameter 1 512 30 1 ! |
|
| Автор: | Geniu$$ [ 09 фев 2010, 07:56 ] |
| Заголовок сообщения: | |
Попробуйте добавить в 10000-й пир номер телефона вместо dest F Я думаю из-за того, что у вас там F адпак не видит пир. 21 <NetCon 2> : Voip Peer is NULL. Get default codec class и ставит кодеки по дефолту. |
|
| Страница 1 из 1 | Часовой пояс: UTC |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|