СвязьПроект
http://old.xdsl.ru/svpro/

AP200B + AP200D
http://old.xdsl.ru/svpro/viewtopic.php?f=4&t=263		 Страница 1 из 1
Автор:  keySEE [ 24 окт 2008, 11:08 ]
Заголовок сообщения:  AP200B + AP200D
Добрый день!

Имеется схема из AP200B + AP200D.

Звоню на линию, подключенную к FXO порту - звонок приходит на FXS порт, но поднимаю трубку - тишина...
Если просто поднять трубку на FXS - то тоже тишина.
Автор:  keySEE [ 24 окт 2008, 11:30 ]
Заголовок сообщения:  Конфиги AP200B и AP200D
AP200D
sh run
!
version 8.23I
!
hostname AP200
!
!
no bridge spanning-tree
!
!
no ip-share enable
!
interface ether0.0
ip address 10.1.1.147 255.255.255.0
!
interface ether1.0
no ip address
!
snmp name AP200D
snmp enable-trap dn-register 300
!
no arp reset
!
!
!
!
!
! VoIP configuration.
!
!
! Voice service voip configuration.
!
voice service voip
fax protocol t38 redundancy 0
fax rate 9600
h323 call start fast
h323 call tunnel enable
!
!
! Voice port configuration.
!
! FXO
voice-port 0/0
connection plar 301
no caller-id enable
!
!
! FXO
voice-port 0/1
no caller-id enable
!
!
!
!
! Pots peer configuration.
!
dial-peer voice 2 pots
destination-pattern 101
port 0/0
!
!
!
! Voip peer configuration.
!
dial-peer voice 1 voip
destination-pattern 301
session target 10.1.1.146
voice-class codec 1
dtmf-relay h245-signal
vad
!
!
!
!
!
!
! Gateway configuration.
!
gateway
h323-id voip.10.1.1.147
no ignore-msg-from-other-gk
!
!
! Codec classes configuration.
!
voice class codec 1
codec preference 1 g7231r63
codec preference 2 g7231r53
codec preference 3 g729
codec preference 4 g711alaw
!
!
!
! SIP UA configuration.
!
sip-ua
!
!
! MGCP configuration.
!
mgcp
codec g711ulaw
vad
!
!
! Tones
!
!
!
!
AP200#

и:

AP200B
sh run
!
version 8.30R
!
hostname AP200
!
!
no bridge spanning-tree
!
!
no ip-share enable
!
interface ether0.0
ip address 10.1.1.146 255.255.255.0
!
interface ether1.0
no ip address
!
snmp name AP200B
snmp enable-trap dn-register 300 forcely-block
!
no arp reset
!
pnp-sktelink debug on
!
!
!
!
!
! VoIP configuration.
!
!
! Voice service voip configuration.
!
voice service voip
fax protocol t38 redundancy 0
fax rate 9600
h323 call start fast
h323 call tunnel enable
busyout monitor gatekeeper
busyout monitor sip-server
no busyout monitor callagent
busyout monitor voip-interface
!
!
! Voice port configuration.
!
! FXS
voice-port 0/0
connection plar 101
caller-id enable
!
!
! FXS
voice-port 0/1
caller-id enable
!
!
!
!
! Pots peer configuration.
!
dial-peer voice 1 pots
destination-pattern 301
port 0/0
!
!
!
! Voip peer configuration.
!
dial-peer voice 2 voip
destination-pattern 101
session target 10.1.1.147
voice-class codec 1
vad
dtmf-relay h245-signal
!
!
!
!
!
!
! Gateway configuration.
!
gateway
h323-id voip.10.1.1.146
no ignore-msg-from-other-gk
!
!
! Codec classes configuration.
!
voice class codec 1
codec preference 1 g7231r63
codec preference 2 g7231r53
codec preference 3 g729
codec preference 4 g711alaw
!
!
!
! SIP UA configuration.
!
sip-ua
!
!
! MGCP configuration.
!
mgcp
codec g711ulaw
vad
!
!
! Tones
!
!
!
!
AP200#
Автор:  keySEE [ 24 окт 2008, 11:54 ]
Заголовок сообщения:  Дебаги
FXO debug rta ipc:

[1978.755] VM(0/0/0) Rx FXO Ring Actv
[1978.755] VM(0/0/0) Tx RING_IND
[1979.960] VM(0/0/0) Rx FXO Ring Idle
[1979.960] VM(0/0/0) Tx PLAR_OFFHOOK_IND
[1979.960] VM(0/0/0) DTMF_Signal enable
[1979.960] VM(0/0/0) set T38 mode STD
[1979.960] VM(0/0/0) Fax rate 9600
[1979.975] RTA(0/0/0) Rx RS_LISTEN_REQ callId=15 ssId=1 G729A
peer=0.0.0.0 mp=23030/23031 hp=0/0
[1980.015] RTA(0/0/0) Rx CC_ALERT_RSP peerId(0/0/0)
[1982.960] VM(0/0/0) Ring Detect timeout
[1982.960] VM(0/0/0) FXO OnHook
[1982.960] VM(0/0/0) Tx DISCONN_CNF
[1982.960] RTA(0/0/0) Rx RS_CLOSE_REQ callId=15 ssId=1 dir=reve
[1982.960] RTA(0/0/0) close Media socket
[1982.960] RTA(0/0/0) close RTCP socket
[1985.750] VM(0/0/0) Rx FXO Ring Actv
[1985.750] VM(0/0/0) Tx RING_IND
[1986.990] VM(0/0/0) Rx FXO Ring Idle
[1986.990] VM(0/0/0) Tx PLAR_OFFHOOK_IND
[1986.990] VM(0/0/0) DTMF_Signal enable
[1986.990] VM(0/0/0) set T38 mode STD
[1986.990] VM(0/0/0) Fax rate 9600
[1987.005] RTA(0/0/0) Rx RS_LISTEN_REQ callId=16 ssId=1 G729A
peer=0.0.0.0 mp=23032/23033 hp=0/0
[1987.045] RTA(0/0/0) Rx CC_ALERT_RSP peerId(0/0/0)
[1988.825] RTA(0/0/0) Rx CC_CONNECT_RSP peerId(0/0/0)
[1988.825] VM(0/0/0) FXO OffHook
[1988.825] VM(0/0/0) vopp enable
[1988.825] VM(0/0/0) Fax enable
[1988.825] VM(0/0/0) play mute
[1988.825] RTA(0/0/0) Rx RS_OPEN_REQ callId=16 ssId=1 G7236
peer=10.1.1.146 mp=23032/23033 hp=23026/23027
[1988.825] VM(0/0/0) vopp idle
[1988.825] VM(0/0/0) start codec replace timer to G7236
[1988.855] VM(0/0/0) Rx RTP codec G723 no change
[1988.885] VM(0/0/0) vopp enable
[1988.885] VM(0/0/0) codec replaced to G7236
[1988.885] VM(0/0/0) Fax enable
[1988.885] VM(0/0/0) play mute
[1995.200] RTA(0/0/0) Rx RS_CLOSE_REQ callId=16 ssId=1 dir=reve
[1995.200] RTA(0/0/0) Rx RS_CLOSE_REQ callId=16 ssId=1 dir=forw
[1995.200] RTA(0/0/0) close Media socket
[1995.200] RTA(0/0/0) close RTCP socket
[1995.200] RTA(0/0/0) Rx AP_SVC_REQ nSvcElem=1 rawDataLen=0
DTMF_STOP
[1995.205] VM(0/0/0) play mute
[1995.205] RTA(0/0/0) Rx CC_DISCONN_REQ CZ=0, peerId(0/0/0)
[1995.205] VM(0/0/0) vopp idle
[1995.205] VM(0/0/0) FXO OnHook
[1995.205] VM(0/0/0) Tx DISCONN_CNF

FXO debug voip call:

115 <CEP 000000> : Call Received
116 <CEP 000000> : Call Initiated : calledNumber() crv(0) total(0)
117 <Call 13> : ****************** Call Created status(InitiatedByFXO) *******************
118 <CEP 000000> : Calling number(101)
119 <CEP 000000> : Call id(cf62ca47-c1ea-4fe4-8017-0002a4044ef8) callNum(13)
120 <Call 13> : MatchAllProcess After Sorted
<0> id(1) dest(301) prefer(0) selected(11)
121 <Call 13> : Initiate callee with dial-peer(301) status(CalleeDeterminedAll) id(cf62ca47-c1ea-4fe4-8017-0002a4044ef8)
122 <NetEP 13> : InitiateOutCall: calledNum(301) callingNum(101) target(10.1.1.146)
123 <NetEP 13> : DoCall: calledAddr(301@10.1.1.146) callingAddr(101)
124 <H323 13> : local capabilities.
number of capabilities = 6
1 : g7231A-6.3k
2 : g729-8k
3 : g711alaw-64k
4 : T.38
5 : UserInput/basicString
6 : UserInput/hookflash
125 <H225 13> : Try signalling TCP connect (10.1.1.146:1720)
126 <H225 13> : Signalling TCP connect success (13)
127 <Q931 13> : Send SETUP
128 <Q931 13> : Received CALL PROCEEDING
129 <Chan 13> : Open - number(101) direction(receive) session(voice) codec(g7231A-6.3k)
- Local : Data(23026) Cont(23027) Addr(10.1.1.147)
- Remote : Data(23020) Cont(23021) DataAddr(10.1.1.146) ContAddr(10.1.1.146)
130 <Q931 13> : Received ALERTING
131 <H245 13> : Send TCS request.
132 <Q931 13> : Send FACILITY
133 <H245 13> : Send MSD request.
134 <Q931 13> : Send FACILITY
135 <Call 13> : Alert from(ffffffff) pseudo(0) inband(0) status(CalleeInitiated)
136 <Q931 13> : Received FACILITY
137 <H245 13> : Received TCS request.
138 <H245 13> : remote capabilities matching to local capabilities.
number of capabilities = 6
1 : g7231A-6.3k
2 : g729-8k
3 : g711alaw-64k
4 : T.38
5 : UserInput/basicString
6 : UserInput/hookflash
139 <H245 13> : Send TCS ack.
140 <Q931 13> : Send FACILITY
141 <Q931 13> : Received FACILITY
142 <H245 13> : Received TCS ack..
143 <Q931 13> : Received FACILITY
144 <H245 13> : Received MSD ack.
145 <H245 13> : Send MSD ack.
146 <Q931 13> : Send FACILITY
147 <CEP 000000> : Disconnected(16) at Busy
148 <Call 13> : Terminated from(0) this(Local:CallClear) before(NULL) forced(0)
149 <CEP 000000> : DisconnectCall at Idle
150 <Chan 13> : Close - number(101) direction(receive)
151 <Q931 13> : Send RELEASE COMPLETE
152 <NetEP 13> : Call TO <voip.10.1.1.146> terminated reason(Local:CallClear)
153 <CEP 000000> : Call Received
154 <CEP 000000> : Call Initiated : calledNumber() crv(0) total(0)
155 <Call 14> : ****************** Call Created status(InitiatedByFXO) *******************
156 <CEP 000000> : Calling number(101)
157 <CEP 000000> : Call id(d662ca47-2ad4-358b-8019-0002a4044ef8) callNum(14)
158 <Call 14> : MatchAllProcess After Sorted
<0> id(1) dest(301) prefer(0) selected(12)
159 <Call 14> : Initiate callee with dial-peer(301) status(CalleeDeterminedAll) id(d662ca47-2ad4-358b-8019-0002a4044ef8)
160 <NetEP 14> : InitiateOutCall: calledNum(301) callingNum(101) target(10.1.1.146)
161 <NetEP 14> : DoCall: calledAddr(301@10.1.1.146) callingAddr(101)
162 <H323 14> : local capabilities.
number of capabilities = 6
1 : g7231A-6.3k
2 : g729-8k
3 : g711alaw-64k
4 : T.38
5 : UserInput/basicString
6 : UserInput/hookflash
163 <H225 14> : Try signalling TCP connect (10.1.1.146:1720)
164 <H225 14> : Signalling TCP connect success (14)
165 <Q931 14> : Send SETUP
166 <Q931 14> : Received CALL PROCEEDING
167 <Chan 14> : Open - number(101) direction(receive) session(voice) codec(g7231A-6.3k)
- Local : Data(23028) Cont(23029) Addr(10.1.1.147)
- Remote : Data(23022) Cont(23023) DataAddr(10.1.1.146) ContAddr(10.1.1.146)
168 <Q931 14> : Received ALERTING
169 <H245 14> : Send TCS request.
170 <Q931 14> : Send FACILITY
171 <H245 14> : Send MSD request.
172 <Q931 14> : Send FACILITY
173 <Call 14> : Alert from(ffffffff) pseudo(0) inband(0) status(CalleeInitiated)
174 <Q931 14> : Received FACILITY
175 <H245 14> : Received TCS request.
176 <H245 14> : remote capabilities matching to local capabilities.
number of capabilities = 6
1 : g7231A-6.3k
2 : g729-8k
3 : g711alaw-64k
4 : T.38
5 : UserInput/basicString
6 : UserInput/hookflash
177 <H245 14> : Send TCS ack.
178 <Q931 14> : Send FACILITY
179 <Q931 14> : Received FACILITY
180 <H245 14> : Received TCS ack..
181 <Q931 14> : Received FACILITY
182 <H245 14> : Received MSD ack.
183 <H245 14> : Send MSD ack.
184 <Q931 14> : Send FACILITY
185 <Q931 14> : Received CONNECT
186 <H225 14> : Remote Endpoint (AddPac VoIP,8.23,97,0,22)
187 <Call 14> : Connected from(ffffffff)
188 <NetEP 14> : Call with voip.10.1.1.146 established
189 <Chan 14> : Open - number(101) direction(transmit) session(voice) codec(g7231A-6.3k)
- Local : Data(23028) Cont(23029) Addr(10.1.1.147)
- Remote : Data(23022) Cont(23023) DataAddr(10.1.1.146) ContAddr(10.1.1.146)
190 <Q931 14> : Received FACILITY
191 <H245 14> : Received EndSession command.
192 <Q931 14> : Received RELEASE COMPLETE
193 <Chan 14> : Close - number(101) direction(receive)
194 <Chan 14> : Close - number(101) directio(transmit)
195 <Call 14> : Terminated from(ffffffff) this(Remote:CallClear) before(NULL) forced(0)
196 <CEP 000000> : DisconnectCall at Busy
197 <CEP 000000> : StopSignal
198 <CEP 000000> : Disconnect (0)
199 <NetEP 14> : Call TO <voip.10.1.1.146> terminated reason(Remote:CallClear)
200 <CEP 000000> : Disconnected(16) at Disconnecting
Автор:  Mi1ovidoff [ 27 окт 2008, 07:12 ]
Заголовок сообщения:  Re: AP200B + AP200D
keySEE писал(а):
Звоню на линию, подключенную к FXO порту - звонок приходит на FXS порт, но поднимаю трубку - тишина...


keySEE, обратитесь пожл. к разделу нашего FAQ по AddPac: если срывается звонок при поднятии трубки на FXS когда он перебрасывается с FXO

Покажите отладку с FXS-сного шлюза AddPac.
Автор:  Denis [ 27 окт 2008, 07:51 ]
Заголовок сообщения:  Re: AP200B + AP200D
Если на AP200 убрать команду connection plar 101 и поднять трубку на телефоне, подключенном к этому порту (0/0) гудок есть?
Автор:  keySEE [ 28 окт 2008, 09:29 ]
Заголовок сообщения:  Re: AP200B + AP200D
Denis писал(а):
Если на AP200 убрать команду connection plar 101 и поднять трубку на телефоне, подключенном к этому порту (0/0) гудок есть?


Вот гудка действительно не было.
FXO 0/0 - пропускает только звонок... Гудков в трубке нет

Решил настроить на FXO 0/1 - и всё заработало с существующими настройками...
Автор:  Denis [ 28 окт 2008, 14:34 ]
Заголовок сообщения:  Re: AP200B + AP200D
keySEE писал(а):
Denis писал(а):
Если на AP200 убрать команду connection plar 101 и поднять трубку на телефоне, подключенном к этому порту (0/0) гудок есть?


Вот гудка действительно не было.
FXO 0/0 - пропускает только звонок... Гудков в трубке нет

Решил настроить на FXO 0/1 - и всё заработало с существующими настройками...


Я имел ввиду адпак с FXS портом. На адпаке с FXO портом у вас прописана данная команда с номером 301, а не 101.
Страница 1 из 1 Часовой пояс: UTC
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/